RK3588 4GB/8GB/16GB/32GB Custom RAM, WF-C3588-M2, AndroidSBC, Reykjavik

TL;DR: RK3588 4GB/8GB/16GB/32GB Custom RAM

SHENZHEN, China, September 12, 2026 - The WF-C3588-M2 board line at Wanlin Longgang closed lot 237 this week. 22,980 units are now booked for Reykjavik, Iceland, shipped FOB with the full certification file attached.

AndroidSBC release of the nine-variant custom RK3588 motherboard platform for OEM and ODM projects serving Reykjavik, Iceland. The line spans custom Android motherboards at the entry variant through core-board-plus-carrier work at the SOM end, all on the same Rockchip RK3588 silicon with 6 TOPS NPU, 8K H.265 decode and up to 32GB of LPDDR5. AndroidSBC ships the full range from the Wanlin Longgang plant, and Reykjavik buyers can mix custom variants inside a single framework agreement rather than opening a new supplier file for each product line.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group. The group runs SMT, test and packing under one roof at Longgang in Shenzhen, and it has built custom boards on Rockchip silicon for overseas OEM customers for over ten years. The WF-C3588 line-up covers nine custom categories on the same Rockchip RK3588 octa-core 8nm silicon with 6 TOPS NPU: custom Android motherboards, custom industrial boards, core board and SOM carrier design, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards. Buyers in Reykjavik and Iceland can source any of the nine custom variants from one factory with one set of export documents.

WF-C3588-M2 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Iceland importers sourcing the WF-Series, the 16GB + 64GB (WF-C3588-M2-C) variant is the typical configuration for the custom core board and SOM plus carrier programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Core Board SOM with Carrier Board Design Service for Iceland Buyers

Buyers in Reykjavik who have sourced a custom core board som with carrier board design service for a few seasons tend to separate two questions: can the factory hold the price, and can it hold the allocation. The second one is harder. The Rockchip RK3588 is allocated at wafer level, and a 22,980-unit order placed against trader stock is the order most likely to slip a quarter without anyone warning the buyer. The second issue is firmware, not hardware. Vendors promise the full certified software stack and then ship a bare AOSP image, and the failure only surfaces at the warehouse when the unit is powered on against the customer's app.

The third exposure is paperwork. Factories that stamp marks without holding the underlying test reports leave the importer to produce a Technical File after the fact, which is exactly when the container is sitting in a bonded yard. The answer AndroidSBC applies is to close the gap at the source. Custom variant assembled on the Longgang line, certified image burned, burn-in record traceable per unit, certification file issued with the lot. The nine WF-C3588 variants span SMARC 2.2 modules, stamp-hole core boards, LGA core boards, COM Express carriers, medical imaging terminals, robotics compute modules, custom carrier designs, and OEM development kits and each carries three memory configurations, which keeps most Iceland requirements on a standard custom SKU rather than a from-scratch run.

Buyers in Iceland tend to ask about the local mark before they ask about price. In Iceland volumes are small and land through Reykjavik, so buyers typically consolidate orders with a European distributor rather than importing directly. AndroidSBC handles that by preparing the destination-market file covering CE/EEA conformity with PTA radio interface notification administered by PTA Iceland alongside the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), with the lot routed through Port of Reykjavik on the Reykjavik to Rotterdam relay.

Competitive Comparison: WF-C3588-M2 vs Competing RK3588 Boards

Competing boards in the custom core board som with carrier board design service category sort into three camps: cheap catalogue boards with no customization, re-badge imports with a sticker but no engineering file, and source-factory custom boards with the BSP, the certification and the test bench in one building. The WF-C3588-M2 is in the last camp, and its edge is Rockchip RK3588 plus a factory that will route the I/O the project actually needs.

• vs standard SOM catalogues: the WF-C3588-M2 either matches SMARC 2.2 exactly or the carrier is redesigned around the project, so the module never forces the product.
• vs two-vendor module plus carrier splits: core board and carrier come from one desk, one schematic review and one test plan, which removes the finger-pointing stage entirely.
• vs closed-module vendors: BSP source, SDK and documentation ship with the project, so a customer engineering team can maintain the carrier after delivery.
• vs re-branded modules: the SI report and the thermal map are Longgang documents, not forwarded PDFs from a third party.

Global Custom SOM and Core Board Market Trends

The Custom SOM and Core Board curve is what Iceland importers read before committing to a custom core board som with carrier board design service programme. The number they quote is the Edge AI hardware segment at USD 26.9 billion in 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), which serves as the closest public proxy for the silicon demand behind custom RK3588 boards. For Reykjavik that resolves into three demand patterns across the WF-C3588 order book:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-M2 board carries that headroom without a board change.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.

Channel research on the Custom SOM and Core Board segment keeps landing on the same point: the constraint is allocation, and allocation is held by factories rather than traders.

Across those three segments, Reykjavik procurement has been shifting from spot quotes to framework agreements with a one-lot-per-month cadence, particularly where a custom Android, industrial, signage or robotics programme needs a twelve-month shipping window.

Partner Success Story: Borealis Fleet Systems in Reykjavik, Iceland

Borealis Fleet Systems, a fleet telematics provider serving the Iceland market, deployed 4,100 custom WF-C3588-A0 Android boards for commercial vehicle telematics terminals. The rollout covered the medical imaging terminal, custom smarc migration, and machine vision carrier workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 4,100 custom WF-C3588-A0 Android boards for commercial vehicle telematics terminals
• Region: Reykjavik, Iceland
• Models used: WF-C3588-M2 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shekou with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Reykjavik via the Reykjavik to Rotterdam relay

"Wide DC input, wide temperature, and a locked Android build with our telematics stack pre-installed. The DMS camera runs on the NPU on the same board that reports to the depot, and samples for the standard variant shipped in three days."

- Piotr Nowak, Engineering Manager

Field Report: a high-brightness outdoor display trial in Reykjavik, where 22,980 units of the WF-C3588-M2 board are running behind sunlight-readable panels

Reporter Jiang Bo, on the ground in Reykjavik, Iceland. The trial ran the WF-C3588-M2 boards inside a sealed enclosure with no active cooling and a panel brightness pushed to its ceiling. Internal board temperature stabilised below the throttle point across a full day of direct sun, and the content loop ran without a dropped frame from morning to evening.

The QA lead noted that the WF-C3588-M2 lot was the third consecutive run to clear the aging bench without a retest.

The inspection confirmed three things on the spot: the WF-C3588-M2 units hold the burn-in with a yield above 99.18 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE/EEA conformity with PTA radio interface notification administered by PTA Iceland, cleared for entry at Port of Reykjavik on the Reykjavik to Rotterdam relay. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Iceland importers can hand straight to their customs broker.

Filed by Jiang Bo, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-M2 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-M2 (Custom Core Board SOM with Carrier Board Design Service) as the lead SKU for Reykjavik and Iceland programmes:

• Medical imaging terminal: a device maker keeps its regulatory file intact by swapping the core board and reusing the validated carrier.
• Robotics compute module: an AMR maker takes the stamp-hole core board and designs a slim carrier for a new chassis generation.
• Custom SMARC migration: a legacy SMARC installation moves to RK3588 with a pin-compatible carrier revision and keeps the enclosure.
• OEM development kit: a product team gets the reference carrier, the SDK and the BSP source and prototypes before committing to tooling.
• LGA core board programme: a display brand solders the core board directly onto its own mainboard for a locked BOM.
• Machine vision carrier: a vision integrator routes MIPI CSI-2 lanes to four cameras and lets the NPU carry the inspection model.
• Fleet compute module: a telematics supplier builds one carrier for three vehicle programmes and swaps memory options per contract.
• Lab instrumentation: an instrument maker keeps a decade-old enclosure alive by replacing only the core board and the BSP.

Partnership Models for Reykjavik Buyers

AndroidSBC opens the WF-C3588 to Iceland partners through three structures, and a single agreement can draw on more than one:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from the Wanlin Longgang source factory in Shenzhen under the same per-lot documentation pack. For Reykjavik buyers, a typical first order on the WF-C3588-M2 is the 16GB + 64GB (WF-C3588-M2-C) configuration at MOQ 5,000 units per shipment, with standard-variant samples in 1-3 days and 15-30 days to mass production on custom runs.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: The customization scope runs across five layers: hardware (PCB, PCBA, I/O, memory, storage), thermal (fanless passive, vented, wide-temperature, conformal coating), software (custom ROM, custom Linux, pre-installed apps, OTA), branding (logo, packaging, boot animation, SKU labels), and compliance (the certification file assembled for the exact configuration you ship). Most Iceland partners change two or three layers on a standard variant rather than commissioning a full custom run.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Custom ROM, custom BSP and custom SDK work are all part of the ODM tier. AndroidSBC builds the Android image (12, 13, 14 or 15, GMS or AOSP), ports the Linux BSP to your carrier revision, and releases the SDK modules your team needs under NDA. The engineering desk carries the port itself, so a Iceland integrator is not left debugging an unmodified vendor BSP against a carrier it was never designed for.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: The NPU is fully open on the custom line. Bring the model in PyTorch, ONNX, TensorFlow or Caffe and the Longgang desk handles the RKNN quantization, the runtime integration and the validation against your board's thermal and memory profile. Custom AI algorithm integration is a standard line item on the ODM scope, and the resulting model ships embedded in the firmware image burned per lot.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for Iceland, and who handles them?

Answer: Yes, and the file travels with the goods. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with the EMC and safety reports for your configuration, dated within the prior year. AndroidSBC confirms any Iceland-specific addition at quotation stage, which is the point where the answer is still useful rather than expensive.

How long will AndroidSBC keep supplying a custom board?

Answer: The commitment is seven years minimum on supply, with security patches back-ported across the Android and Linux firmware tracks and OTA infrastructure for pushing firmware and RKNN model updates to deployed units. Long-lifecycle programmes in industrial, signage and robotics usually ask for the term in writing, and it is written.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes. AndroidSBC ships DDP to Amazon FBA warehouses in the US, EU and Japan, and to nominated 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton labelling and pallet configuration follow FBA inbound requirements, the export declaration names the Wanlin Longgang source factory as the place of origin, and each pallet carries a per-unit barcode that traces back to the burn-in record for downstream RMAs.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-C3588 line, measured over the prior twelve months. On RMA, the partner returns the faulty WF-C3588-M2 unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record and the configuration file are attached per unit, the failure analysis normally comes back with a root cause rather than a credit note, which matters when a custom configuration is holding up a production line.

Contact AndroidSBC: Start Your WF-C3588-M2 Sourcing Conversation

AndroidSBC is the export channel for the Wanlin WF-C3588 custom board line. Buyers in Reykjavik and Iceland looking to source the WF-C3588-M2 straight from the source factory can use any of the following:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE/EEA conformity with PTA radio interface notification for Iceland, administered by PTA Iceland, entering at Port of Reykjavik on the Reykjavik to Rotterdam relay
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

Custom board enquiries move fastest when the first message carries three things: annual volume, customization scope and Incoterm. With those in hand the export desk returns a per-lot quote and the WF-C3588 MOQ matrix inside two business days.